DXDM280BT
INSTALLATION/OWNER'S MANUAL
AM/FM/CD Receiver
DXDM280BT INSTALLATION
Decorative
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
• Remove 2 transit screws located on top of the unit.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
• Test for correct operation.
• Snap trim ring into place.
2
Bezel
TYPICAL FRONT-LOAD DIN
MOUNTING METHOD
DXDM280BT INSTALLATION
Wiring Diagram
L-CH
SUBREARFRONT
10 AMP
AGC Fuse
R-CH
Antenna
Connector
FUSE
When replacing the
fuse, make sure new
fuse is the correct type
and amperage. Using
an incorrect fuse could
damage the radio.
The unit uses one 10 amp
AGC fuse located beside
the wiring connector.
3
DXDM280BT OPERATION
Control Locations
18 1 2 3
4
5
Preset 1 / Repeat
1 10
Preset 2 / Random
2 11
Preset 3 / Intro
3 12
Power / Mute
4 13
5 14
Tune / Track Down
76
8
9
10
11
Bluetooth Talk
Auxiliary Input
Audio / Menu
USB Input
Display
12
13
17
16
15
14
Tune / Track Up
6 15
Mode
7 16
Band / Go Back
8 17
Volume Knob
9 18
4
Preset 6 / Folder Up
Preset 5 / Folder Down
Preset 4 / Play / Pause
Eject
DXDM280BT OPERATION
Remote Control
17
16
15
14
13
12
Mode
1
Volume Up
2
Power
3
Select
4
Tune / Track Up
5
Volume Down
6
Band / Go Back
7
Preset 3 / Intro
8
9
Preset 2 / Random
1
2
3
4
5
6
7
8
9
10
11
Preset 6 / Folder Up
10
Mute
11
Audio / Menu
12
Preset 5 / Folder Down
13
Preset 4 / Play / Pause
14
15
Preset 1 / Repeat
16
Bluetooth Talk
17
Tune / Track Down
5
DXDM280BT OPERATION
General Operation
Power On/Off
Mode
Auxiliary Input
Volume
Display
Reset
Set the Clock
12/24-hour Clock
Setup Menu
Press on. Press to turn the unit off.
Press MODE to select between AM/FM, CD player, Bluetooth, auxiliary and USB. Modes of operation are shown in the display.
NOTE: CD and USB modes will not appear unless a CD is inserted or USB device is connected.
The DXDM280BT offers a 3.5 mm auxiliary input port on the front panel of the unit for connecting an audio device, MP3 player, etc. Press MODE to select auxiliary input mode.
Adjust volume using volume knob (00-46).
Press DISP to show the clock. During playback of MP3/files, ID3 tag information, elapsed time, track number and file/ folder names will automatically rotate on the display.
Press RESET upon initial installation or if abnormal operation occurs.
With the unit on, press and hold DISP until the clock begins to flash, then release. Press the ll button to adjust the HOUR and press the nn to adjust the minutes.
The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold AUDIO for more than 3 seconds to access the setup menu. Press AUDIO momentarily to select between the menu functions and rotate the volume knob left/right to adjust or activate the desired function.
or any other button (except EJECT) to turn the unit
6
DXDM280BT OPERATION
General Operation - Setup Menu
Menu Function Options Action
Auto Station
Store
Local/Distance
Tuning
Tuner
Frequency
Spacing
Auxiliary Input
Beep
Confirmation
Programmable
Turn On Volume
Power On
Message
Scrolling
Option
Demonstration
Mode
Bluetooth
Auto Answer
AUTO STORE
LOCAL OFF Activates distance tuning (Tuner mode only).
LOCAL ON
FREQ USA
FREQ EURO
AUX ON Enables the front panel 3.5mm auxiliary input.
AUX OFF Disables the front panel 3.5mm auxiliary input.
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
PRO-VOL #
MSG OFF Disables power on message. (Example: GOOD MORNING)
MSG ON Enables power on message to be displayed.
SCROLL 15 SP Programs unit to scroll information every 15 seconds (default).
SCROLL ONCE
SCROLL ON
SCROLL OFF Programs the unit to show the first 10 characters on display.
DEMO OFF Disables the demonstration mode.
DEMO ON Enables the demonstration mode.
BT ON Enables Bluetooth functionality.
BT OFF Disables Bluetooth functionality.
ANSWER
Auto
ANSWER
Manual
Press the volume knob to seek and save 6 strong stations in the current band. (Tuner mode only)
Activates local tuning for strong station reception only (Tuner mode only).
Programs the unit to USA tuner spacing. (200kHz for FM and 10kHz for AM). (Tuner mode only)
Programs the unit to European tuner spacing. (50kHz for FM and 9kHz for AM). (Tuner mode only)
Programs unit to always turn on at a specific volume (default is OFF). Any volume level 1-30 can be selected.
Programs unit to scroll once then show the first 10 characters on display
Programs unit to scroll continuously.
Programs unit to automatically answer every incoming phone call after 2-3 rings.
Programs unit to require the answer incoming phone calls (default).
button must be pressed to
7
DXDM280BT OPERATION
General Operation
Audio
Bass
Treble
Balance
Fader
EQ
Loudness
Source Volume Level
Press AUDIO momentarily to select between Bass, Treble, Balance and Fader.
BASS TREBLE BALANCE FADER EQ LOUD SOURCE LEVEL
Press AUDIO until BASS appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Press AUDIO until TREBLE appears then rotate volume knob left/right to adjust ( -6 minimum / +6 maximum).
Press AUDIO until BAL appears then rotate volume knob left/right to adjust
BAL EVEN represents equal balance
Press AUDIO until FAD appears then rotate volume knob left/right to adjust (FAD 12R - FAD 12F). FAD EVEN represents equal fader
Press EQ, then turn the volume knob to cycle through the following equalization curves: FLAT (default), POP, JAZZ, CLASSIC, BEAT, ROCK and USER. Any manual adjustment to the Bass or Treble settings are automatically saved as USER.
Press AUDIO/MENU until LOUD appears then rotate volume knob left/right to adjust LOUD ON/OFF.
The source volume level control allows a gain adjustment for each audio source: AM, FM, CD, AUX and USB. Set the source volume level for each mode, depending on the relative volume of each audio source.
(BAL 12L - BAL 12R).
To set the source volume level, press AUDIO/MENU until SRC LEVEL appears. After one second, the current mode will appear on the display. Turn the volume knob to adjust the audio level of the current source (-3 minimum/+3 maximum).
Note: Only the current mode will be available for adjustment. To adjust another mode of operation, press MODE until the desired mode is selected, then set the source volume level for that mode.
8
Loading...